![]() Appropriate safety precautions must be taken. An act of demolition is required for their removal. Power fasteners are a permanently installed fixture. Green is lowest power level, red is highest power level. Remington power load strips are available in three power levels – green (level 3), yellow (level 4) and red (level 5). Safety Precautions Start 22 27 CALIBER GREEN POWER LEVEL 3 YELLOW POWER LEVEL 4 5 4 3 2 7 1 1 RED POWER LEVEL 5 8 9 10 11 12 NICKEL BRASS 6 482-54 NOTE: Failure to start with the lowest power level can result in overdrive condition and will result in damage to tool (See page 13). If the tool still fails to fire, hold the tool firmly against the work surface for another 30 seconds before advancing the power load strip. Again press the tool firmly against the work surface and pull the trigger. Release the trigger and remove pressure on the tool while holding the muzzle against the work surface. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds. TOO THIN 3/16" MIN Do not drive power fasteners into steel base material less then 3/16" thick, within 2" of a weld, within 1/2" of the edge or within 1" of another power fastener. ![]() Do not drive power fasteners into concrete less than three times as thick as the intended fastener penetration, within 3" of the edge, within 3" of another power fastener or within 3" of a failed power fastener. Never drive power fasteners into thin or easily penetrated materials unless it is backed by concrete or steel. Never make fastenings in spalled or cracked areas. Materials of this type tend to shatter and create hazard from flying particles. Never attempt to drive power fasteners into very hard or brittle materials including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel. Safety Precautions CAST IRON GLASS TILE BRICK 482-33 2. KNOW YOUR FASTENING BASE MATERIAL ? Sinks in with average hammer blow ? CENTER PUNCH TEST TOO SOFT 482-28 482-27 482-26 Start Point flattens GREEN POWER LEVEL 3 Surface shatters YELLOW POWER LEVEL 4 TOO HARD 1. Never drink alcoholic beverages or take medications which impair your vision, balance or judgement before using a powder actuated tool. An operator taking medication should take extra precautions while handling the tool. If the tool is dropped, inspect for damage and repair it before continuing to work. Never point a powder actuated tool at anyone. ![]() Never carry or pass a loaded powder actuated tool. Keep power loads of different power levels in separate containers. Store powder actuated tool and power load strips in a locked container. Safety Precautions POWD LOAD POWDER LOADS 3. Never place your finger on the trigger until the tool’s muzzle is against the work surface. Accidental discharge can cause serious injury. Make sure the work area is clean from loose material and debris. ![]() Always clear the work area on all sides and post appropriate warning signs on job sites. Safety Precautions WARNING POWDER ACTUATED TOOLS IN USE ! 482-10 4. WARNING: This tool is designed only for use by qualified operators. We expressly disclaim any liability for any injury to persons or damage to property which result from your failure to take the precautions contained in this manual. Improper use of this tool can cause serious injury or death from firing fastener into body or from flying debris. Warning: Safety Precautions IMPORTANT: Read these operating instructions carefully and completely before trying to operate or service this tool. This manual should always accompany the tool and be transferred with it upon change of ownership. G 029 G 028 Operating Instructions 482-1 Important: Read this manual and all labels carefully before operating your powder actuated tool. REMINGTON ® Powerdriver NDENT LAB OR PE DE ST ® I FO R P U B LI C ™ Y TE NG FE T AN Y OR AT IN Model 491 SA POWDER ACTUATED TOOL MANUFACTURERS´ INSTITUTE INC.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |